氣體吸附式變干機

◆物料優點 Product features

※有著維持一樣的的吸氣壓強和露點

1.吸收塔之寬度與內徑經實驗英文結杲精密制造計算公式，塔床進而導致阻力小，提高了減少氣態太干劑5秒的碰觸時間段，充分考慮制成品氣的露點想要。

2.30％的常溫、皮膚干劑空間，于補償費用常溫、皮膚干劑的自動脆化，有效確保常溫、皮膚干。

3.特大型吸附器，提高認識暖濕氣流勻稱按照干熱劑層，排除溝流現像。

※降解氣量自然損耗需小于14％

1.領航的機筒規劃，永久保存100％的粘附發含糖量，保存的發含糖量用來增多重復周期的重復氣的溫度，從而提高機器設備的解吸性能，不使重復更完全。

2.低溫干燥和降解使用反相煙囪效應實施方案，濕熱空氣流走干的吸附劑劑追訴時效果最佳。降解氣出口到含濕量調整在亞達到飽和程序程序，使消音器及排氣閥門節點無結霜之慮。

3.可按照變干機的正常運作負載電阻供給改善二次利用氣含量，保障二次利用氣團聯續不穩定性，二次利用學習壓力低至臨界點。

※低溫干燥劑應用使用期限長

1.剛好合適的機筒的尺寸，使氣體根據干熱劑層的流動速度和時光維持好的階段，更加充分派揮干熱劑的耐熱性。

2.適宜的體統運行環境，在氣體進去機筒前，經除油凈化處理不能清理掉氣體中內含油率物與重感染源物，逃避干熱劑層受感染源。

※機主要包括了新鮮高的質量自行及氣動彈簧閥和耐用的全電子可代碼序控制模塊，人與機器工具欄友誼，自行重復屏幕上顯示雙塔工作狀況，配置周期時間現場視頻可編，設備設置好10min。電動閥門期限過去了50萬次操作。

※筒身內腔作冷熱浸鋅防銹化處里，10年不脫漆。

※動作最準確、使用性能安全穩定、操作步驟簡單，的安裝沒有基本知識。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆核心技術參數設置 Main technical parameters